Bobbin work allows you to embroider designs with beautiful textured threads and ribbon— threads that cannot be sewn through the needle. For best results, you not only need a specially digitized design but you need to modify your technique and make some machine adjustments.
Please note: Bobbin work requires some testing and adjusting of your machine tensions. Please refer to your machine manual or consult your sewing machine dealer for specific help with your machine.
Supplies
- Design specifically digitized for bobbin work
- Heavier threads such as Pearl Crown Rayon, 2mm silk ribbon, Madeira Decora 6, other decorative threads and fibers generally used for bobbin work. (Note: Heavier yarns are not recommended due to the short amount you will be able to wind on the bobbin.)
- Monofilament invisible (polyester or nylon) upper thread
- 70/10 or 75/11 embroidery needle
- Specialty or second bobbin case
- Screw driver for adjusting bobbin case tension
- Fabric, stabilizer
Preparation: Filling the Bobbin
Bobbins can be wound by hand or by machine. If winding by machine, wind slowly. Since you probably will not be able to run the thread through the normal thread guides, use your fingers to control the winding tension. Be careful not to wind too tightly or too loosely.
Be sure to check the amount of thread on the bobbin each time you start a new design. If the bobbin runs out during stitching:
- Remove the hoop
- Thread the “tail” to the back (top side of hoop_ using the tapestry or chenille needle
- Wind and insert a new bobbin
- Replace the hoop
- Reposition the needle to where the “tail” comes to the back
- Bring the bobbin thread to the wrong side by hand as when beginning a design
- Continue stitching the design
Avoid using heavier yarns as you will not be able to wind enough on the bobbin to complete a single design. I tried winding a textured knitting yarn and only got about 30” on the bobbin before it was full.
Preparation: Machine Tensions
Most home embroidery machines have automatic tensioning that cause the top (needle) thread to be pulled to the bottom side of the hooped fabric. This is perfect for traditional embroidery because under proper tensions, the bobbin thread will never be seen on the design side.
However, with bobbin work, the design will be sewn on the bobbin side using thread many times heavier than embroidery bobbin thread. Also, monofilament thread is quite thin and slips through the tensions easily. These three issues will require tension adjustments to accommodate the thread weights and to prevent the monofilament from pulling through to the design side.
Proper bobbin and needle thread tensions will take some trials. Use a small design and be sure to test with the same weight and type of thread you will be using in your project.
Using a separate bobbin case for bobbin work will make switching between specialty stitching and standard easier and more enjoyable. Be sure to label your bobbin cases if they do not look different. Be sure to read the manual for your machine; some threads may be so heavy that bypassing certain tensioners is the best route. I found that with Pearl Crown Rayon I had to loosen the tension screw on the bobbin case quite a bit (be careful not to unscrew it all the way!) and raise the needle thread tension for a good result.
How much should you loosen the tension? I suggest inserting embroidery bobbin thread in your regular case and feeling the tension of the thread as you pull it through the bobbin. This should give an idea for what the tension should feel like after adjusting for a heavier thread. If you have a front loading bobbin case, you might try the “bobbin drop test.” Hold the threaded bobbin in one hand by the thread tail with the other hand cupped a few inches below. Give a little jerk on the tail and see if the bobbin drops a bit. If the bobbin doesn’t drop, loosen some more; if it drops a lot, tighten a bit.
Allow plenty of time for testing since you can’t see the results until you remove the hoop from the machine because they are on the bottom. Chances are that you won’t be pulling these heavy threads to the back of the embroidery but you don’t want the needle thread pulled to the design side.
While you’re at your machine, turn off the automatic thread cutter if your machine has one and slow your machine down.
Preparation: Fabric
The only trick here is remembering that the right side of the fabric faces the bed of the machine and the stabilizer goes on top. In general, bobbin work designs are open and lower stitch count, which means a lower distortion type of design. Choose an appropriate stabilizer for the fabric. I prefer to use a light-weight, no-show cutaway when the stabilizer can stay in. Tearaways can be difficult to remove since these designs do not have a lot of needle penetrations to perforate this type of stabilizer. You may want to choose a water soluble product.
Embroidering the Design
Advance your machine to the first stitch in the design. Manually turn the hand wheel of the machine to pull the bobbin thread to the top. Many machines will sink the needle in the center of the design and then travel to the first stitch. If you pull the thread up here and the design doesn’t start in the center, you will probably end up embroidering over a long thread tail later in the design.
Hold both thread tails for the first couple of stitches; do not trim.
You may get better stitch formation if you slow your machine down.
When the design is finished, leave a bobbin thread tail several inches long. Pull the bobbin thread to the back or use a tapestry needle to inserted near the stitch to bring the tail to the wrong side. Tie off the starting and ending thread tail with a knot close to the fabric to secure if desired and trim threads to about one inch long.
Other Notes:
You will need to change the bobbin whenever you want to switch to a new color. Stop the machine, remove the hoop and follow the steps for running out of thread.
